12 x 3050 SMD Warm White LEDs and 6 x dual brightness 5050 LEDs for combined Number Plate Illumination, Stop and Tail lamp funtion. Multi direction bulb with 6 Volt application with equal pin BA15D base. 3000k warm white 360 degree light and bright RED colour temperature from 6 high power red LEDS. Red and white LEDs illuminate for tail light/number plate illumination functions - RED light intensifies when the brake is applied. Good contrast between red stop and tail light outputs. A great combination lamp.  Accepts 6 to 9V input voltage in POSITIVE EARTH Very low current draw - over 75% less than incandescent and halogen bulbs so great for low powered electrical systems. 18mm maximum diameter, 32mm total bulb height. The red light output is not quite as bright as the BAY15D part numbers (CSTLEDWWR-12Y, CSTLEDWWR-6NY and CSTLEDWWR-6PY) with their two cree LEDs behind a lens, but this is still a very bright, compact lamp, so a great option where space is limited - the ideal LED combination conversion lamp for Lucas Type L582 lamps with the BA15D fitting.

High performance LED flasher unit/relay designed for vintage and classic applications including different types of bulb/LED. 3 pin with Earth wire. A very flexible flasher unit that is ideal for use on vehicles that are changed in full or part to LED stop/tail lights and or indicator/turn signals. In testing these units deliver consistant flashing at the correct rate, whether installed in a circuit with all incandescent bulbs, all LED bulbs, a mix of incandescent and LED bulbs, a mix of incandescent bulbs and LED panels or a mix of LED bulbs and LED panels! Available for 6V, 12V, Negative or Positive Earth systems to cover all applications. Please select the version you require. A great solution when upgrading to LED funcionality on most classic or modern cars and motor cycles. X, L, P and Earth wire (which must be connected) terminals. X Live (49), L Load (indicator switch, 49a), P Pilot/warning light. Dimensions = 36mm height x 33mm diameter Should any flashing irregularity be experienced on cars with unsuppressed HT leads, fit an inline suppressor - part number 292SUP - in the ignition king lead between coil and distributor. --

High performance LED flasher unit/relay designed for vintage and classic applications including different types of bulb/LED. 3 pin with Earth wire. A very flexible flasher unit that is ideal for use on vehicles that are changed in full or part to LED stop/tail lights and or indicator/turn signals. In testing these units deliver consistant flashing at the correct rate, whether installed in a circuit with all incandescent bulbs, all LED bulbs, a mix of incandescent and LED bulbs, a mix of incandescent bulbs and LED panels or a mix of LED bulbs and LED panels! Available for 6V, 12V, Negative or Positive Earth systems to cover all applications. Please select the version you require. A great solution when upgrading to LED funcionality on most classic or modern cars and motor cycles. X, L, P and Earth wire (which must be connected) terminals. X Live (49), L Load (indicator switch, 49a), P Pilot/warning light. Dimensions = 36mm height x 33mm diameter Should any flashing irregularity be experienced on cars with unsuppressed HT leads, fit an inline suppressor - part number 292SUP - in the ignition king lead between coil and distributor. --

High performance LED flasher unit/relay designed for vintage and classic applications including different types of bulb/LED. 3 pin with Earth wire. A very flexible flasher unit that is ideal for use on vehicles that are changed in full or part to LED stop/tail lights and or indicator/turn signals. In testing these units deliver consistant flashing at the correct rate, whether installed in a circuit with all incandescent bulbs, all LED bulbs, a mix of incandescent and LED bulbs, a mix of incandescent bulbs and LED panels or a mix of LED bulbs and LED panels! Available for 6V, 12V, Negative or Positive Earth systems to cover all applications. Please select the version you require. A great solution when upgrading to LED funcionality on most classic or modern cars and motor cycles. X, L, P and Earth wire (which must be connected) terminals. X Live (49), L Load (indicator switch, 49a), P Pilot/warning light. Dimensions = 36mm height x 33mm diameter Should any flashing irregularity be experienced on cars with unsuppressed HT leads, fit an inline suppressor - part number 292SUP - in the ignition king lead between coil and distributor.

High performance LED flasher unit/relay designed for vintage and classic applications including different types of bulb/LED. 3 pin with Earth wire. A very flexible flasher unit that is ideal for use on vehicles that are changed in full or part to LED stop/tail lights and or indicator/turn signals. In testing these units deliver consistant flashing at the correct rate, whether installed in a circuit with all incandescent bulbs, all LED bulbs, a mix of incandescent and LED bulbs, a mix of incandescent bulbs and LED panels or a mix of LED bulbs and LED panels! Available for 6V, 12V, Negative or Positive Earth systems to cover all applications. Please select the version you require. A great solution when upgrading to LED funcionality on most classic or modern cars and motor cycles. X, L, P and Earth wire (which must be connected) terminals. X Live (49), L Load (indicator switch, 49a), P Pilot/warning light. Dimensions = 36mm height x 33mm diameter Should any flashing irregularity be experienced on cars with unsuppressed HT leads, fit an inline suppressor - part number 292SUP - in the ignition king lead between coil and distributor. --

High performance LED flasher unit/relay designed for vintage and classic applications including different types of bulb/LED. 3 pin with Earth wire. A very flexible flasher unit that is ideal for use on vehicles that are changed in full or part to LED stop/tail lights and or indicator/turn signals. In testing these units deliver consistant flashing at the correct rate, whether installed in a circuit with all incandescent bulbs, all LED bulbs, a mix of incandescent and LED bulbs, a mix of incandescent bulbs and LED panels or a mix of LED bulbs and LED panels! Available for 6V, 12V, Negative or Positive Earth systems to cover all applications. Please select the version you require. A great solution when upgrading to LED funcionality on most classic or modern cars and motor cycles. X, L, P and Earth wire (which must be connected) terminals. X Live (49), L Load (indicator switch, 49a), P Pilot/warning light. Dimensions = 36mm height x 33mm diameter Should any flashing irregularity be experienced on cars with unsuppressed HT leads, fit an inline suppressor - part number 292SUP - in the ignition king lead between coil and distributor. --

30 x 4014 SMD LED BA15D 6 & 12 Volt multi-directional 600 Lumen warm white lamp. Combined Stop & Tail (Brake & Rear) functionality. LED upgrade and replacement for B381B and B3212A double filament type bulbs with BA15D double contact base. Dual polarity. In testing, comparable in brightness to conventional 5/21W bulbs with the benefits of LED. Very low current draw - over 75% less than incandescent and halogen bulbs so great for low powered electrical systems. 3000K warm, white colour temperature. Maximum diameter 18mm, total bulb height 43mm. For a brighter white light pelase see B381LEDW and for a red version of this dual brightness lamp see B381LEDR

30 x 4014 SMD LED BA15D 6 &12 Volt multi-directional 600 Lumen bright white lamp. Combined Stop & Tail (Brake & Rear) functionality. LED upgrade and replacement for B381B and B3212A double filament type bulbs with BA15D double contact base. Dual polarity. Comparable in brightness to conventional 5/21W bulbs in testing, with the benefits of LED. Very low current draw - over 75% less than incandescent and halogen bulbs so great for low powered electrical systems. 6000K bright, white colour temperature. Maximum diameter 18mm, total bulb height 43mm. For a warm white version of theis LED see B381LEDWW and B381LEDR for a red version.

12 x 3014 SMD LED BA15D 12 Volt multi-directional warm white lamp. LED upgrade for B209B c5w single contact bulbs with BA15D double contact base. Much brighter than 5W bulbs in testing. Clear glass 19mm diameter LED cover. Compatible with either negative or positive earth systems. Very low current draw - over 75% less than incandescent and halogen bulbs so great for low powered electrical systems. 3000K warm, white colour temperature. A really neat bulb for vintage and classic vehicles - LED performance with the look of a conventional bulb.

12 x 3014 SMD LED BA15D 6 Volt multi-directional warm white lamp. Dual brightness LED bulb with 6 to 9v input voltage range. BA15D double contact base. Clear glass 19mm diameter LED cover. Compatible with either negative or positive earth systems. Very low current draw - over 75% less than incandescent and halogen bulbs so great for low powered electrical systems. 3000K warm, white colour temperature. A really neat bulb for vintage and classic vehicles - LED performance with the look of a conventional bulb. Wire the preferred brightness.

12 x 3014 SMD LED BA15S 12 Volt multi-directional warm white lamp. LED upgrade and replacement for B207B and B245B. In testing, brighter than B245B (10W). BA15S base. Clear glass 19mm diameter LED cover. Compatible with either negative or positive earth systems. Very low current draw - over 75% less than incandescent and halogen bulbs so great for low powered electrical systems. 3000K warm, white colour temperature. A really neat bulb for vintage and classic vehicles - LED performance with the look of a conventional bulb.

12 x 3014 SMD LED BA15S 12 Volt multi-directional bright white lamp. LED upgrade and replacement for B207B and B245B. In testing, brighter than B245B (10W). BA15S base. Clear glass 19mm diameter LED cover. Compatible with either negative or positive earth systems. Very low current draw - over 75% less than incandescent and halogen bulbs so great for low powered electrical systems. 6000K bright, white colour temperature. A really neat bulb for vintage and classic vehicles - LED performance with the look of a conventional bulb.

12 x 3014 SMD LED BA15S 6 Volt multi-directional warm white lamp. LED upgrade and replacement for B205. BA15S base. In testing, comparable in brightness to 6V incandescent bulb B205 (5W). Clear glass 19mm diameter LED cover. Compatible with either negative or positive earth systems. Very low current draw - over 75% less than incandescent and halogen bulbs so great for low powered electrical systems. 3000K warm, white colour temperature. A really neat bulb for vintage and classic vehicles - LED performance with the look of a conventional bulb.

8 x 5050 SMD LED BA15S 12 Volt multi-directional warm white lamp. LED upgrade and direct replacement for B309A. BA15S base. Brighter than original c15W bulbs. Compatible with either negative or positive earth systems. Very low current draw - over 75% less than incandescent and halogen bulbs so great for low powered electrical systems. 3000K warm, white colour temperature. Applications include sidelights and repeaters, warning lights and number plate lights. 35mm total bulb length, 19mm maximum head diameter, no cover.

9 x 5050 SMD LED BA15S 12 Volt multi-directional warm white lamp. LED upgrade and replacement for B309A. Brighter in testing than incandescent c15W bulb B309A. Compatible with either negative or positive earth systems. Very low current draw - over 75% less than incandescent and halogen bulbs so great for low powered electrical systems. 3000K warm, white colour temperature. Applications include sidelights and repeaters, warning and number plate lights.

8 x 5050 SMD LED BA15S 12 Volt multi-directional bright white lamp. LED upgrade and direct replacement for B309A. BA15S base. Brighter than original 12V c15W bulbs. Compatible with either negative or positive earth systems. Very low current draw - over 75% less than incandescent and halogen bulbs so great for low powered electrical systems. 6000K bright, white colour temperature. Applications include sidelights and repeaters, warning and number plate lights. 35mm total bulb length, 19mm maximum head diameter, no cover.

9 x 5050 SMD LED BA15S 12 Volt multi-directional bright white lamp. LED upgrade and replacement for B309A. LED equivalent to incandescent 12V c15W bulbs. Compatible with either negative or positive earth systems. Very low current draw - over 75% less than incandescent and halogen bulbs so great for low powered electrical systems. 6000K bright, white colour temperature. Applications include sidelights, repeaters, warning and number plate lights.

8 x 5050 SMD LED BA15D 6 Volt multi-directional bright white lamp. LED upgrade and direct replacement for B315. BA15D base. Brighter than original c10W bulbs. Compatible with either negative or positive earth systems. Very low current draw - over 75% less than incandescent and halogen bulbs so great for low powered electrical systems. 6000K bright, white colour temperature. Applications include sidelights and repeaters, dash lights and number plate lights. 35mm total bulb length, 19mm maximum head diameter, no cover. For a warm white version see part number B315LEDWW.

8 x 5050 SMD LED BA15D 6 Volt multi-directional warm white lamp. LED upgrade and direct replacement for B315. BA15D base. Brighter than original c10W bulbs. Compatible with either negative or positive earth systems. Very low current draw - over 75% less than incandescent and halogen bulbs so great for low powered electrical systems. 3000K warm, white colour temperature. Applications include sidelights and repeaters, dash lights and number plate lights. 35mm total bulb length, 19mm maximum head diameter, no cover. For a bright white version please see part number B315LEDW

8 x 5050 SMD LED BA15S 6 Volt multi-directional warm white lamp. LED upgrade and direct replacement for B244. BA15S base. Brighter than original c10W bulbs. In testing, brighter than 6V incandescent bulb B244B. Compatible with either negative or positive earth systems. Very low current draw - over 75% less than incandescent and halogen bulbs so great for low powered electrical systems. 3000K warm, white colour temperature. Applications include sidelights and repeaters, dash lights and number plate lights. 35mm total bulb length, 19mm maximum head diameter, no cover.

9 x 5050 SMD LED BA15S 6 Volt multi-directional warm white lamp. LED upgrade and direct replacement for B244. LED equivalent to c10W bulbs. In testing, brighter than 6V incandescent bulb B244B. Compatible with either negative or positive earth systems. Very low current draw - over 75% less than incandescent and halogen bulbs so great for low powered electrical systems. 3000K warm, white colour temperature. Applications include sidelights and repeaters, dash lights and number plate lights. 37mm total bulb length, 20mm head diameter, no cover.

8 x 5050 SMD LED BA15S 6 Volt multi-directional bright white lamp. LED upgrade and direct replacement for B244. BA15S base. Brighter than original c10W bulbs. In testing, brighter than 6V incandescent bulb B244B. Compatible with either negative or positive earth systems. Very low current draw - over 75% less than incandescent and halogen bulbs so great for low powered electrical systems. 6000K bright, white colour temperature. Applications include sidelights and repeaters, dash lights and number plate lights. 35mm total bulb length, 19mm maximum head diameter, no cover.

9 x 5050 SMD LED BA15S 6 Volt multi-directional bright white lamp. LED upgrade and direct replacement for B244. LED equivalent to c10W bulbs. In testing, brighter than 6V incandescent bulb B244B. Compatible with either negative or positive earth systems. Very low current draw - over 75% less than incandescent and halogen bulbs so great for low powered electrical systems. 6000K bright, white colour temperature. Applications include sidelights and repeaters, dash lights and number plate lights. 37mm total bulb length, 20mm head diameter, no cover.

6 x 5730 SMD LED WEDGE T10 12 Volt multi-directional WHITE lamp. Very bright 5730 LEDs. A great white LED upgrade bulb for B955 (16W) with T15 WEDGE base. Compatible with either negative or positive earth systems. Very low current draw - over 75% less than incandescent and halogen bulbs so great for low powered electrical systems. Bright White 6000k colour temperature. Much brighter in testing than B955 (16W) and more comparable with B921 (21W). For even brighter LED altenatives with integral lenses, please see part numbers B921ALED and B921LEDW

5 x 5050 SMD LED WEDGE T10 12 Volt multi-directional warm white lamp. LED upgrade and replacement for B501 T10 WEDGE type bulbs. Compatible with either negative or positive earth systems. Very low current draw - over 75% less than incandescent and halogen bulbs so great for low powered electrical systems. 3000K warm, white colour temperature. 29mm total bulb height, 11mm LED section diameter. A very popular LED bulb. For LED alternatives of comparable brightness please see B501LEDW-A and B117LEDWW-A

5 x 5050 SMD LED WEDGE T10 12 Volt multi-directional bright white lamp. LED upgrade and replacement for B501 T10 WEDGE type bulbs. Compatible with either negative or positive earth systems. Very low current draw - over 75% less than incandescent and halogen bulbs so great for low powered electrical systems. 6000K bright, white colour temperature. 29mm total bulb height, 11mm LED section diameter. A very popumar LED bulb. For LED alternatives of comparable brightness please see B501LEDWW-A and B117LEDWW-A

8 x 2835 SMD LED WEDGE T10 12 Volt multi-directional warm white lamp. LED upgrade and replacement for B504 3W and B501 5W bulbs with WEDGE T10 base. Brighter than conventional 5W bulb. Compatible with either negative or positive earth systems. Very low current draw - over 75% less than incandescent and halogen bulbs so great for low powered electrical systems. 3000K warm, white colour temperature. 12mm maximum diameter, 22mm total bulb height. For a bright white light see part number B501LEDW-B, for brighter alternatives see part numbers B501LEDWW-A and B117LEDWW-A

8 x 2835 SMD LED WEDGE T10 12 Volt multi-directional bright white lamp. LED upgrade and replacement for B501 and B510H with WEDGE T10 base. Brighter than conventional 5W bulbs in testing. Compatible with either negative or positive earth systems. Very low current draw - over 75% less than incandescent and halogen bulbs so great for low powered electrical systems. 6000K bright, white colour temperature. 12mm maximum diameter, 22mm total bulb height. For a warm white light see part number B501LEDWW-B, for brighter alternatives see part numbers B501LEDWW-A and B117LEDWW-A

20 x 2835 SMD LED WEDGE T10 12 Volt multi-directional very bright white lamp. LED upgrade bulb with WEDGE T10 base. Brighter in testing than T15 bulbs B922 (10W) and comparable to B955 (16W). Compatible with negative or positive earth systems. Very low current draw - over 75% less than incandescent and halogen bulbs so great for low powered electrical systems. 6000K bright, white colour temperature. 32mm total bulb length, 11mm LED section diameter. For a brighter alternative please see part number B501LEDW-D

6 x 5730 SMD LED WEDGE T10 12 Volt multi-directional AMBER lamp. 6 x 5730 LEDs. An Amber LED lamp with T10 WEDGE base comparable in brightness to c5W incandescent lamps. Compatible with either negative or positive earth systems. Very low current draw - over 75% less than incandescent and halogen bulbs so great for low powered electrical systems. AMBER colour temperature.

8 x 2835 SMD LED WEDGE T10 6 Volt multi-directional bright white lamp. LED upgrade and replacement for B117B with WEDGE T10 base. Brighter than conventional 5W bulb. Compatible with either negative or positive earth systems. Very low current draw - over 75% less than incandescent and halogen bulbs so great for low powered electrical systems. 6000K bright, white colour temperature. 12mm maximum diameter, 22mm total bulb height. For some 6V T10 LED alternatives please see B117LEDWW-A, B117ALEDWW and B500LEDW-C

8 x 2835 SMD LED WEDGE T10 6 Volt multi-directional warm white lamp. LED upgrade and replacement for B117A with WEDGE T10 base. Brighter than conventional 3W bulb. Compatible with either negative or positive earth systems. Very low current draw - over 75% less than incandescent and halogen bulbs so great for low powered electrical systems. 3000K warm, white colour temperature. 12mm maximum diameter, 22mm total bulb height. For some brighter 6V T10 LED alternatives please see B117LEDWW-A, B117BLEDW and B500LEDW-C

80 Lumen Osram LED WEDGE T10 multi-directional warm white lamp, with diffused glass bulb. Accepts input voltages between 6 and 45V. A high specification LED upgrade and replacement for B117B type bulbs with WEDGE T10 base. Compatible with either negative or positive earth systems. Very low current draw - over 75% less than incandescent and halogen bulbs so great for low powered electrical systems. 3000K warm, white colour temperature. 10mm maximum diameter, 26mm total bulb height. Much brighter than B117B in testing. For other 6V T10 LED alternatives please see B117ALEDWW, B117BLEDW and B117LEDW-A

80 Lumen Osram LED WEDGE T10 multi-directional bright white lamp, with diffused glass bulb. Accepts input voltages between 6 and 45V. A high specification LED upgrade and replacement for 5W bulbs with WEDGE T10 base e.g. B117B, B501, B507. Compatible with either negative or positive earth systems. Very low current draw - over 75% less than incandescent and halogen bulbs so great for low powered electrical systems. 6000K bright, white colour temperature. 10mm maximum diameter, 26mm total bulb height. Much brighter than B117B and B501 in testing. For other 6V T10 LED alternatives please see B117ALEDWW, B117BLEDW and B117LEDWW-A

Warm White 8 x 2835 SMD 50 Lumen LED 12V lamp with flat LED cluster for single direction light applications. MES E10 base. Brighter than original c5W bulbs. Compatible with either negative or positive earth systems. Very low current draw - over 75% less than incandescent and halogen bulbs so great for low powered electrical systems. 3000K warm, white colour temperature. 12mm maximum diameter, 19mm total bulb height.

8 x 2835 SMD LED MES E10 12 Volt multi-directional warm white lamp. LED upgrade and replacement for B208 type bulbs. MES E10 base. Brighter than original c5W bulbs. Compatible with either negative or positive earth systems. Very low current draw - over 75% less than incandescent and halogen bulbs so great for low powered electrical systems. 3000K warm, white colour temperature. 12mm maximum diameter, 23mm total bulb height.

Bright White 8 x 2835 SMD 50 Lumen LED 12V lamp with flat LED cluster for single direction light applications. MES E10 base. Brighter than original c5W bulbs. Compatible with either negative or positive earth systems. Very low current draw - over 75% less than incandescent and halogen bulbs so great for low powered electrical systems. 6000K bright, white colour temperature. 12mm maximum diameter, 19mm total bulb height.

9 x 1210 SMD 50 Lumen LED 6V lamp with flat LED cluster for single direction light applications. MES E10 base. Equivalent to original c4W bulbs. Compatible with either negative or positive earth systems. Very low current draw - over 75% less than incandescent and halogen bulbs so great for low powered electrical systems. 3000K warm, white colour temperature. 12mm maximum diameter, 18mm total bulb height.

8 x 2835 SMD LED MES E10 6 Volt multi-directional warm white lamp. LED upgrade and replacement for B950 type bulbs. MES E10 base. Brighter than original c5W bulbs. Compatible with either negative or positive earth systems. Very low current draw - over 75% less than incandescent and halogen bulbs so great for low powered electrical systems. 3000K warm, white colour temperature. 12mm maximum diameter, 23mm total bulb height.

9 x 1210 SMD 50 Lumen LED 6V lamp with flat LED cluster for single direction light applications. MES E10 base. Equivalent to original c5W bulbs. Compatible with either negative or positive earth systems. Very low current draw - over 75% less than incandescent and halogen bulbs so great for low powered electrical systems. 6000K bright, white colour temperature. 12mm maximum diameter, 18mm total bulb height.

4 x 3030 SMD LED MES E10 12 Volt multi-directional bright white lamp. LED upgrade and replacement for B987B type bulbs. MES E10 base. T10 tubular glass cover. Compatible with either negative or positive earth systems. Very low current draw - over 75% less than incandescent and halogen bulbs so great for low powered electrical systems. 3000K warm, white colour temperature. 29mm total length.

4 x 3030 SMD LED MES E10 6 Volt multi-directional bright white lamp. LED upgrade and replacement for B990 type bulbs. MES E10 base. Brighter than original c2W bulbs. Compatible with either negative or positive earth systems. Very low current draw - over 75% less than incandescent and halogen bulbs so great for low powered electrical systems. 3000K warm, white colour temperature.

5 x 5050 SMD 80 Lumen LED 12 Volt multi-directional, bright white lamp. LED upgrade bulb with BA9S base. Comparable in brightness to B992 10W incandescent bulbs (Much brighter than B233 (4W) bulbs). Compatible with either negative or positive earth systems. Very low current draw - over 75% less than incandescent and halogen bulbs so great for low powered electrical systems. 6000K bright, white colour temperature. 29mm total bulb length, 12mm LED section diameter.

5 x 5050 SMD 80 Lumen LED 12 Volt multi-directional, warm white lamp. LED upgrade bulb with BA9S base. Much brighter than B233B c4W incandescent bulbs in testing. Compatible with either negative or positive earth systems. Very low current draw - over 75% less than incandescent and halogen bulbs so great for low powered electrical systems. 3000K warm, white colour temperature. 29mm total bulb length, 12mm LED section diameter.

80 Lumen Osram BA9S multi-directional warm white lamp with diffused glass bulb. Accepts input voltages between 5 and 45V. LED upgrade and replacement for many bulbs with BA9s base. Compatible with either negative or positive earth systems. Very low current draw - over 75% less than incandescent and halogen bulbs so great for low powered electrical systems. 3000K warm, white colour temperature. 10mm maximum diameter, 26mm total bulb height.

80 Lumen Osram BA9S multi-directional bright white lamp with diffused glass bulb. Accepts input voltages between 5 and 45V. LED upgrade and replacement for many bulbs with BA9s base. Compatible with either negative or positive earth systems. Very low current draw - over 75% less than incandescent and halogen bulbs so great for low powered electrical systems. 6000K bright, white colour temperature. 10mm maximum diameter, 26mm total bulb height.

8 x 2835 SMD 50 Lumen LED 6V lamp with flat LED cluster for single direction light applications. BA9S base. Equivalent to original c4W bulbs. Compatible with either negative or positive earth systems. Very low current draw - over 75% less than incandescent and halogen bulbs so great for low powered electrical systems. 3000K warm, white colour temperature. 12mm maximum diameter and 18mm total bulb length.

8 x 2835 SMD 50 Lumen LED 6V lamp with flat LED cluster for single direction light applications. BA9S base. Equivalent to original c4W bulbs. Compatible with either negative or positive earth systems. Very low current draw - over 75% less than incandescent and halogen bulbs so great for low powered electrical systems. 6000K bright, white colour temperature. 12mm maximum diameter and 18mm total bulb length.

5 x 5050 SMD 80 Lumen LED 6 Volt multi-directional, warm white lamp. LED upgrade and direct replacement for B293 and B951. BA9S base. Proving brighter than c6W incandescent bulb in testing. Compatible with either negative or positive earth systems. Very low current draw - over 75% less than incandescent and halogen bulbs so great for low powered electrical systems. 3000K warm, white colour temperature. 29mm total bulb length, 12mm LED section diameter. For a bright white light please see part number B293LEDW-A, for less bright LED options please see part number B293LEDW-B and B293LEDWW-B

5 x 5050 SMD 80 Lumen LED 6 Volt multi-directional, bright white lamp. LED upgrade and direct replacement for B293 and B591. BA9S base. Proving brighter than c6W incandescent bulbs in testing. Compatible with either negative or positive earth systems. Very low current draw - over 75% less than incandescent and halogen bulbs so great for low powered electrical systems. 6000K bright, white colour temperature. 29mm total bulb height, 11mm LED section diameter. For a warm white light please see part number B293LEDWW-A, for less bright LED options please see part number B293LEDW-B and B293LEDWW-B

9 x 1210 SMD 50 Lumen LED 6V lamp with flat LED cluster for single direction light applications. BA9S base. Equivalent to original c4W bulbs and a good LED upgrade option for incandescent bulb B293B. Compatible with either negative or positive earth systems. Very low current draw - over 75% less than incandescent and halogen bulbs so great for low powered electrical systems. 6000K bright, white colour temperature. 12mm maximum diameter and 18mm total bulb length. For a warm white version please see part number B293LEDWW-B and for brighter alternatives B293LEDW-A and B293LEDWW-A

8 x 2835 SMD 50 Lumen LED 6V lamp with flat LED cluster for single direction light applications. BA9S base. Equivalent to original c4W bulbs and a good LED upgrade option for incandescent bulb B293B. Compatible with either negative or positive earth systems. Very low current draw - over 75% less than incandescent and halogen bulbs so great for low powered electrical systems. 3000K warm, white colour temperature. 12mm maximum diameter and 18mm total bulb length. For a bright white version please see part number B293LEDW-B and for brighter alternatives B293LEDW-A and B293LEDWW-A

4 x 3030 SMD LED MCC BA9S 12 Volt multi-directional bright white lamp. LED upgrade and replacement for B288B 2W incandescent bulbs. BA9S base. T10 (10mm diameter) tubular glass cover. Much brighter than c2W bulbs - actually brighter than 4W B233B type bulbs in testing. Compatible with either negative or positive earth systems. Very low current draw - over 75% less than incandescent and halogen bulbs so great for low powered electrical systems. 6000K bright, white colour temperature. 29mm total bulb length. For a brighter alternative please see part number B233LEDWW

4 x 3030 SMD LED MCC BA9S 6 Volt multi-directional bright white lamp. A neat LED upgrade for B287, proving significantly brighter in testing. BA9S base. Much brighter than original c2W bulbs. Compatible with either negative or positive earth systems. Very low current draw - over 75% less than incandescent and halogen bulbs so great for low powered electrical systems. 6000K bright, white colour temperature. 100 diameter tubular glass cover, 29mm total bulb length.

4 x 3528 SMD LED BA7S 12 Volt multi-directional bright white lamp. LED upgrade and replacement for B281B. BA7S base. Brighter than original c2W bulbs. Compatible with either negative or positive earth systems. Very low current draw - over 75% less than incandescent and halogen bulbs so great for low powered electrical systems. 6000K bright, white colour temperature.

1 x 3030 SMD LED BA7S 12 Volt bright white lamp. BA7S base for low wattage instrument applications. Compatible with either negative or positive earth systems. Very low current draw - over 75% less than incandescent and halogen bulbs so great for low powered electrical systems. 6000K bright, white colour temperature. 9mm maximum diameter, 15mm total bulb height.

4 x 3528 SMD LED BA7S 6 Volt multi-directional bright white lamp. LED upgrade and direct replacement for B282. BA7S base. Brighter than original c2W bulbs. Compatible with either negative or positive earth systems. Very low current draw - over 75% less than incandescent and halogen bulbs so great for low powered electrical systems. 6000K bright, white colour temperature.

1 x 3030 SMD LED BA7S 6 Volt bright white lamp. BA7S base for low wattage instrument applications. Compatible with either negative or positive earth systems. Very low current draw - over 75% less than incandescent and halogen bulbs so great for low powered electrical systems. 6000K bright, white colour temperature. 9mm maximum diameter, 15mm total bulb height.

Very bright 5 Cree LED MCC BA9S multi-directional bright AMBER lamp. Accepts voltage input 10 to 30V. LED upgrade bulb with BA9S base comparable in brightness to 23W amber incandescent bulb B418. Compatible with either negative or positive earth systems. Very low current draw - over 75% less than incandescent and halogen bulbs so great for low powered electrical systems. Bright AMBER colour temperature. Indicator application. Integral lens, 12.5mm head diameter, 45mm diameter overall bulb length. For correct indicator function an electronic flasher relay will be required of the correct polarity for your vehicle and also pin configuration, to suit your current wiring arrangement. Most commonly 12V, 3 pin, negative earth/ground LEDFLASH3. For a bright white version of this bulb, please see part number B419LEDW

30 x 4014 SMD LED BA15S 6 Volt multi-directional 600 lumen bright AMBER lamp. LED upgrade and replacement for B317 type single filament bulb. BA15S base. Brighter than conventional 21W bulbs. Compatible with either negative or positive earth systems. Very low current draw - over 75% less than incandescent and halogen bulbs so great for low powered electrical systems. Bright AMBER colour temperature. Best behind a clear lens in indicator applications - use B317LEDWW behind amber lenses. For correct indicator function an electronic flasher relay will be required of the correct polarity for your vehicle and also pin configuration, to suit your current wiring arrangement. Most commonly 12V, 3 pin, negative earth/ground LEDFLASH3. Maximum diameter 18mm, total bulb height 43mm.

30 x 4014 SMD LED BA15S 12 Volt multi-directional, 600 lumen, single brightness, bright RED lamp. LED upgrade and replacement for B382BR type single filament bulb. BA15S base. In testing, 50% brighter than conventional 21W incandescent bulb B382BR. Compatible with either negative or positive earth systems. Very low current draw - over 75% less than incandescent and halogen bulbs so great for low powered electrical systems. Bright RED colour temperature. This is NOT a combined stop & tail function bulb. Maximum diameter 18mm, total bulb height 43mm.

12 x 3020 SMD LED multi-directional super bright WHITE reversing lamp. Accepts 10 to 40V input voltage. LED upgrade for 12V B382B and 24V B241/B290 type single filament indicator bulbs. BA15S base. Much brighter than conventional incandescent bulbs in testing - twice as bright as 21W bulbs. Brighter than LED lamp B382LEDW also. Compatible with both NEGATIVE and POSITIVE earth systems. Very low current draw - over 75% less than incandescent and halogen bulbs so great for low powered electrical systems. Bright WHITE colour temperature. If used as an indicator an electronic flasher relay will be required of the correct polarity for your vehicle and also pin configuration, to suit your current wiring arrangement. Most commonly 12V, 3 pin, negative earth/ground LEDFLASH3. Though B382LEDAS and B382LEDWWS (behind amber lenses) are better for indicator application. 19mm maximum diameter, 47mm total bulb height. A warm white version of this super bright WHITE bulb is also available - please see part number B382LEDWWS.

12 x 3020 SMD LED multi-directional super bright AMBER indicator lamp. Accepts 10 to 40V input voltage. LED upgrade for 12V B343B and 24V B241A type single filament indicator bulbs. BA15S base. Much brighter than conventional incandescent bulbs in testing - twice as bright as 21W bulbs. Brighter than LED lamp B382LEDA also. Compatible with both NEGATIVE and POSITIVE earth systems. Very low current draw - over 75% less than incandescent and halogen bulbs so great for low powered electrical systems. Bright AMBER colour temperature. Great results behind a clear and amber lenses. For correct indicator function an electronic flasher relay will be required of the correct polarity for your vehicle and also pin configuration, to suit your current wiring arrangement. Most commonly 12V, 3 pin, negative earth/ground LEDFLASH3. 19mm maximum diameter, 47mm total bulb height. Double contact BA15D versions of this super bright AMBER bulb are also available - please see part numbers B382LEDADP (Positive Earth) and B382LEDADP (Negative Earth)

12 x 3020 SMD LED multi-directional super bright AMBER indicator lamp. Accepts 10 to 40V input voltage. AMBER LED upgrade for single filament indicator bulbs with BA15D double contact base. An Amber version of B335B. Much brighter than conventional 12V amber incandescent bulbs in testing (e.g. B343B) - twice as bright as 21W bulbs. Compatible with POSITIVE earth systems only - for negative earth version see B382LEDADN. Very low current draw - over 75% less than incandescent and halogen bulbs so great for low powered electrical systems. Bright AMBER colour temperature. Good results behind clear and amber lenses. For correct indicator function an electronic flasher relay will be required of the correct polarity for your vehicle and also pin configuration, to suit your current wiring arrangement. 19mm maximum diameter, 47mm total bulb height. For single contact version of this bulb see B382LEDAS

12 x 3020 SMD LED multi-directional super bright AMBER indicator lamp. Accepts 10 to 40V input voltage. AMBER LED upgrade for single filament indicator bulbs with BA15D double contact base. An Amber version of B335B. Much brighter than conventional 21W amber incandescent bulbs in testing (e.g. B343B) - twice as bright as 21W bulbs. Compatible with NEGATIVE earth systems only - for positive earth version see B382LEDADP. Very low current draw - over 75% less than incandescent and halogen bulbs so great for low powered electrical systems. Bright AMBER colour temperature. Good results behind clear and amber lenses. For correct indicator function an electronic flasher relay will be required of the correct polarity for your vehicle and also pin configuration, to suit your current wiring arrangement. Most commonly 12V, 3 pin, negative earth/ground LEDFLASH3. 19mm maximum diameter, 47mm total bulb height. For single contact version of this bulb see B382LEDAS

30 x 4014 SMD LED BA15S 12 Volt multi-directional 600 lumen bright AMBER lamp. LED upgrade and replacement for 12V B343B type single filament bulbs. BA15S base. In testing, over 20% brighter than conventional 21W bulbs. Compatible with either negative or positive earth systems. Very low current draw - over 75% less than incandescent and halogen bulbs so great for low powered electrical systems. Bright AMBER colour temperature. Best behind a clear lens in indicator applications - use B382LEDWW behind amber lenses. For correct indicator function an electronic flasher relay will be required of the correct polarity for your vehicle and also pin configuration, to suit your current wiring arrangement. Most commonly 12V, 3 pin, negative earth/ground LEDFLASH3. Maximum diameter 18mm, total bulb height 43mm. For an even brighter 12V (or 24V) AMBER BA15S LED bulb upgrade, please see part number B382LEDAS

30 x 4014 SMD LED BA15S 12 Volt multi-directional bright white lamp. LED upgrade and replacement for B382B single filament type bulb. BA15S base. In testing, approximately 30% brighter than conventional 21W incandescent bulb B382B, more comparable to 23W bulb B337B. Compatible with either negative or positive earth systems. Very low current draw - over 75% less than incandescent and halogen bulbs so great for low powered electrical systems. 6000K bright, white colour temperature. Good for Reverse applications, though the bright white colour temperature can 'wash out' coloured lenses, so  B382LEDWW or B382LEDA are better for indicator applications with amber and clear lenses respectively. Maximum diameter 18mm, total bulb height 43mm.

12 x 3020 SMD LED multi-directional WARM WHITE warning/indicator lamp. Accepts 10 to 40V input voltage. LED upgrade for 12V B382B and 24V B241/B290 type single filament indicator bulbs. BA15S base. Much brighter than conventional incandescent bulbs in testing - twice as bright as 21W bulbs. Brighter than LED lamp B382LEDWW also. Compatible with both NEGATIVE and POSITIVE earth systems. Very low current draw - over 75% less than incandescent and halogen bulbs so great for low powered electrical systems. WARM WHITE 3000k colour temperature. Warm white is good for behind amber lenses. If used as an indicator an electronic flasher relay will be required of the correct polarity for your vehicle and also pin configuration, to suit your current wiring arrangement. Most commonly 12V, 3 pin, negative earth/ground LEDFLASH3. For an AMBER version of this bulb please see part number B382LEDAS 19mm maximum diameter, 47mm total bulb height. A bright white 6000k colour temperature version of this warm white bulb is also available - please see part number B382LEDWS.

15 x 42mm Festoon bulb - equivalent fitting to B1240B and good upgrade option for that bulb proving much brighter in testing. 180 degree light from 6 x SMD 5730 LEDs. These LEDS are brighter than 5050 LEDs and hence the bulb features a finned aluminium heat sink on the rear. Compatible with either negative or positive earth systems. Very low current draw - over 75% less than incandescent and halogen bulbs so great for low powered electrical systems. 6000K bright, white colour temperature. 12.5mm wide LED section.

11 x 42mm 6 Volt Festoon bulb - equivalent fitting to B618F and good LED replacement option for that bulb with comparable brightness in testing. Bright 360 degree light from 24 x 3014 SMD LEDs. Tubular glass cover for LEDs. Compatible with either negative or positive earth systems. Very low current draw - over 75% less than incandescent and halogen bulbs so great for low powered electrical systems. 6000K bright, white colour temperature. For a brighter LED upgrade - brighter than B818LEDW-B and B618F - please see part number B818LEDW-A

15 x 39mm 12V Festoon bulb - equivalent fitting to B239B, though much brighter in testing than 21W B273B. 180 degree light from 6 x SMD 5730 LEDs. These LEDS are brighter than 5050 LEDs and hence the bulb features a finned aluminium heat sink on the rear. Compatible with either negative or positive earth systems. Very low current draw - over 75% less than incandescent and halogen bulbs so great for low powered electrical systems. 6000K bright, white colour temperature. 12.5mm body width. For less bright 39mm LED alternatives please see B273LEDW-B and B273LEDW-C

15 x 42mm 12V (& 24V) Festoon bulb - equivalent fitting to B270B though brighter in testing than 21W B273B. 180 degree light from 12 x 4014 LEDs. Input voltage 10 to 30V. Finned aluminium heat sink on rear. Compatible with either negative or positive earth systems. Very low current draw - over 75% less than incandescent and halogen bulbs so great for low powered electrical systems. 6000K bright, white colour temperature. 13mm wide LED section. For a less bright LED alternative please see B270LEDW-A

9 x 39mm 12V Festoon bulb - equivalent fitting to B239B though brighter than 21W B273B. 180 degree light from 6 x 4014 LEDs. Compatible with either negative or positive earth systems. Very low current draw - over 75% less than incandescent and halogen bulbs so great for low powered electrical systems. 6000K bright, white colour temperature. Tubular glass cover over LEDs. For other bright LED options with a 39mm fitting please see B273LEDW-B and B273LEDW-E. 

9 x 39mm 12V (& 24V) Festoon bulb - equivalent fitting to B239B but brighter than 21W B273B. 180 degree light from 6 x 4014 LEDs. With tubular glass cover. Input voltage 10 to 30V. Compatible with either negative or positive earth systems. Very low current draw - over 75% less than incandescent and halogen bulbs so great for low powered electrical systems. 6000K bright, white colour temperature. 8.5mm LED section diameter. For other bright LED options with a 39mm fitting please see B273LEDW-C and B273LEDW-E. 

8 x 36mm 12V Festoon bulb - equivalent fitting to B257B though brightner in testing than 21W B273B. 180 degree light from 6 x 4014 LEDs. Tubular glass cover for LED section. Compatible with either negative or positive earth systems. Accepts 10 to 30V input voltage. Very low current draw - over 75% less than incandescent and halogen bulbs so great for low powered electrical systems. 6000K bright, white colour temperature.

15 x 42mm 12VFestoon bulb - equivalent fitting to B270B and B273B with brightness comparable to 21W. Bright 360 degree light from 24 x 3014 SMD LEDs. Tubular glass cover for LEDs. Compatible with either negative or positive earth systems. Very low current draw - over 75% less than incandescent and halogen bulbs so great for low powered electrical systems. 6000K bright, white colour temperature. 10mm LED section diameter. For a much brighter 42mm LED festoon option, please see part number B273LEDW-D

11 x 36mm 12V Festoon bulb - equivalent fitting to B257B and a great LED upgrade for that incandescent bulb, proving brighter in testing. 360 degree/all round bright light from 12 x SMD 5050 LEDs. Compatible with either negative or positive earth systems. Very low current draw - over 75% less than incandescent and halogen bulbs so great for low powered electrical systems. 6000K bright, white colour temperature. 11mm LED section diameter, no cover.

11x36mm 12V Festoon bulb - equivalent fitting to B256. 180 degree light from 4 x SMD 5050 LEDs. Compatible with either negative or positive earth systems. Very low current draw - over 75% less than incandescent and halogen bulbs so great for low powered electrical systems. 6000K bright, white colour temperature.

11 x 36mm 6 Volt Festoon bulb - equivalent fitting to B255B and a good upgrade for that bulb. 360 degree/all round bright light from 12 x SMD 5050 LEDs.. Compatible with either negative or positive earth systems. Very low current draw - over 75% less than incandescent and halogen bulbs so great for low powered electrical systems. 6000K bright, white colour temperature. 12mm LED section diameter.

8 x 36mm 6 Volt Festoon bulb - equivalent fitting to B255. 180 degree light from 6 x 5730 SMD LEDs. Compatible with either negative or positive earth systems. Input voltage 5 to 9V. Very low current draw - over 75% less than incandescent and halogen bulbs so great for low powered electrical systems. 6000K bright, white colour temperature.

11 x 36mm 6 Volt Festoon bulb - equivalent fitting to B255. 180 degree light from 4 x SMD 3014 LEDs. Compatible with either negative or positive earth systems. Very low current draw - over 75% less than incandescent and halogen bulbs so great for low powered electrical systems. 6000K bright, white colour temperature.

11 x 39mm Festoon bulb - equivalent fitting to B253. 180 degree light from 6 x SMD 3014 LEDs. Compatible with either negative or positive earth systems. Very low current draw - over 75% less than incandescent and halogen bulbs so great for low powered electrical systems. 6000K bright, white colour temperature.

11 x 39mm 6 Volt Festoon bulb - equivalent fitting to B253B and an upgrade for that 5W bulb, proving much brighter in testing. Very bright 360 degree light from 24 x 3014 SMD LEDs. Compatible with either negative or positive earth systems. Very low current draw - over 75% less than incandescent and halogen bulbs so great for low powered electrical systems. 6000K bright, white colour temperature. 10mm tubular glass cover. For a less bright LED upgrade - though still brighter than B253B - please see B253LEDW-A

11 x 39mm 6 Volt Festoon bulb - equivalent fitting to B253 and a good upgrade for that 5W bulb proving much brighter in testing. 360 degree/all round bright light from 12 x SMD 5050 LEDs. Compatible with either negative or positive earth systems. Very low current draw - over 75% less than incandescent and halogen bulbs so great for low powered electrical systems. 6000K bright, white colour temperature. 12mm diameter LED section, no cover. For an alternative LED upgrade please see B253LEDW-E

11 x 39mm 12V Festoon bulb - equivalent fitting to B239B. 180 degree bright white light from 6 x SMD 3014 LEDs. Compatible with either negative or positive earth systems. Very low current draw - over 75% less than incandescent and halogen bulbs so great for low powered electrical systems. 6000K bright, white colour temperature. 10mm LED section diameter. Comparable to 5W B239B in testing. See also B239LEDW-A and B239LEDW-E for other 39mm festoon LED upgrades.

11 x 39mm 12V Festoon bulb - equivalent fitting to B239, B272. Bright 360 degree light from 24 x 3014 SMD LEDs. Tubular glass LED cover. Compatible with either negative or positive earth systems. Very low current draw - over 75% less than incandescent and halogen bulbs so great for low powered electrical systems. 6000K bright, white colour temperature. Much brighter than 5W B239B in testing, more comparable to 8W. See also B239LEDW-A for another 39mm Festoon LED upgrade.

12 x 3050 SMD Warm White LEDs and 6 x dual brightness 5050 LEDs for combined Number Plate Illumination, Stop and Tail lamp funtion. Multi direction bulb with 6 Volt application with equal pin BA15D base. 3000k warm white 360 degree light and bright RED colour temperature from 6 high power red LEDS. Red and white LEDs illuminate for tail light/number plate illumination functions - RED light intensifies when the brake is applied. Good contrast between red stop and tail light outputs. A great combination lamp.  Accepts 6 to 9V input voltage in NEGATIVE EARTH Very low current draw - over 75% less than incandescent and halogen bulbs so great for low powered electrical systems. 18mm maximum diameter, 32mm total bulb height. The red light output is not quite as bright as the BAY15D part numbers (CSTLEDWWR-12Y, CSTLEDWWR-6NY and CSTLEDWWR-6PY) with their two cree LEDs behind a lens, but this is still a very bright, compact lamp, so a great option where space is limited - the ideal LED combination conversion lamp for Lucas Type L582 lamps with the BA15D fitting.

Combined WARM WHITE and AMBER multi direction, sidelight and indicator bulb. Accepts 6V and 12V input voltages with BA15D base. 12 super bright LEDs with integral lens. Warm white light for sidelight function, changing to very bright AMBER for indication. This bulb should function normally with your existing flasher unit, in the unlikley event of LED 'Hyper flash' an electronic flasher relay will be required of the correct polarity for your vehicle (also pin configuration, to suit your current wiring arrangment). Compatible with either negative or positive earth systems. Very low current draw - over 75% less than incandescent and halogen bulbs so great for low powered electrical systems. 3000K warm, white colour temperature for sidelight, bright amber for indicator. Very flexible application. A great compact and bright solution for easily converting classic sidelights to sidelight/indicator functionality. 18mm maximum diameter, 47mm total bulb height. For a bright white version of this LED lamp please see CSILEDW. For Offset pin BAY15D base versions please see CSILEDWY and CSILEDWWY. 

BA15D fitting. Combined WHITE and AMBER multi-direction, sidelight and indicator bulb. Accepts 6V and 12V input voltages with BA15D base. 12 super bright LEDs with an integral lens. Bright white light for sidelight function, changing to very bright AMBER for indication. This bulb should function normally with your existing flasher unit, in the unlikely event of LED 'Hyper flash' an electronic flasher relay will be required of the correct polarity for your vehicle (also pin configuration, to suit your current wiring arrangement). Compatible with either negative or positive earth systems. Very low current draw - over 75% less than incandescent and halogen bulbs so great for low-powered electrical systems. 6000K bright, white colour temperature for sidelight, bright amber for the indicator. Very flexible application. A great compact and bright solution for easily converting classic sidelights to sidelight/indicator functionality. 18mm maximum diameter, 47mm total bulb height. For a warm white version of this LED lamp please see CSILEDWW. For Offset pin BAY15D base versions please see CSILEDWY and CSILEDWWY.  Base Pin Guide

Kit of two WEDGE T10 base LED bulbs for Lucas type 1130 side lamps that have been converted to SIDE LIGHT & INDICATOR operation with the 424A T10 bulb holder kit (or purchased as 297IND, 297A-IND or 297B-IND complete lamps, with the same 3 x WEDGE T10 bulb holder). Also new sidelamp 1142IND. One very bright AMBER B921ALEDW-A LED bulb and one WHITE Osram LED B117LEDWW-A. Both these high quality bulbs accept 6 and 12 input voltages, so this one kit is suitable for both 6 or 12V vehicles. A simple conversion of these popular lamps to LED operation, as an alternative to LED combination bulbs such as CSILEDWWY - with both options providing good 6V solutions in the absence of a 6V equivalent to 12V incandescent bulb B921A (T10/T15 base 21W bulb). Kit converts one lamp, please buy 2 kits to convert a pair of bulb holders/lamps.

Compact, high power Amber LED that accepts 6 to 24V input voltage. WEDGE T15 W16W type base - so fits the same holders as WEDGE T10 bulbs, just a larger bulb. 360 degree super bright AMBER light. Much brighter in testing than amber T15 incandescent bulb B921A (21W). Compatible with either negative or positive earth systems suitable for 6, 12 or 24V operation. Very low current draw - over 75% less than incandescent and halogen bulbs so great for low powered electrical systems. Bright AMBER colour temperature. Extremely compact 32mm total bulb length, 14mm head diameter. This bulb was specified for WEDGE T10/T15 base applications where space is constrained e.g. in Lucas type 1130 lamps fitted with the '424A' conversion pictured. A great LED bulb (along with high quality Osram LED bulb B117LEDWW-A) to upgrade 1130 lamps already converted to side light and indicator function. For correct indicator function an electronic flasher relay may be required of the correct polarity for your vehicle and also pin configuration, to suit your current wiring arrangement. Most commonly 12V, 3 pin, negative earth/ground LEDFLASH3. For a bright WHITE version of this great LED lamp, please see part number B921LEDW-A

Compact, high power White LED that accepts 6 to 24V input voltage. WEDGE T15 W16W type base - so fits the same holders as WEDGE T10 bulbs, just a larger bulb. 360 degree super bright WHITE light. Much brighter in testing than WHITE T15 incandescent bulb B921 (21W). Compatible with either negative or positive earth systems suitable for 6, 12 or 24V operation. Very low current draw - over 75% less than incandescent and halogen bulbs so great for low powered electrical systems. Bright WHITE colour temperature. Ideal for warning applicatuins e.g reversing light, as well as indicator Extremely compact 32mm total bulb length, 14mm head diameter. This bulb was specified for WEDGE T10/T15 base applications where space is constrained e.g. in Lucas type ST38 lamps fitted with the 'ST38CONV' conversion pictured. A great LED bulb (along with high quality Osram LED bulb B117LEDWW-A) to upgrade ST38/CA1249 lamps already converted to stop and indicator function. For correct indicator function an electronic flasher relay may be required of the correct polarity for your vehicle and also pin configuration, to suit your current wiring arrangement. Most commonly 12V, 3 pin, negative earth/ground LEDFLASH3. For a bright AMBER version of this great LED lamp, please see part number B921ALED-A

8 x 5050 SMD LED BA15S 12 Volt multi-directional RED lamp. Red LED upgrade bulb. In testing much brighter than B207BR, BA15S base. Compatible with either negative or positive earth systems. Very low current draw - over 75% less than incandescent and halogen bulbs so great for low powered electrical systems. RED colour. Applications include rear lights. 37mm total bulb length, 20mm head diameter, no cover.

30 x 4014 SMD LED BA15D 6 Volt multi-directional 600 Lumen bright RED dual brightness LED lamp. Combined Stop & Tail (Brake & Rear) functionality. RED LED option for B383 type 6V double filament type bulbs with BA15D double contact base. RED colour is good for enhancing brightness behind red lenses. Very low current draw - over 75% less than incandescent and halogen bulbs so great for low powered electrical systems. Bright RED colour temperature.

30 x 4014 SMD LED BA15D 6 & 12 Volt multi-directional 600 Lumen bright RED lamp. Combined dual brightness Stop & Tail (Brake & Rear) functionality. RED LED option for B381B type double filament bulbs with BA15D double contact base. Dual polarity. RED LEDs good for enhancing colour behind red lenses. Very low current draw - over 75% less than incandescent and halogen bulbs so great for low powered electrical systems. Bright RED colour temperature. For White and warm white LED versions of B381B please see B381LEDW and B381LEDWW

30 x 4014 SMD LED BA15S 6 Volt multi-directional bright white lamp. LED upgrade and replacement for B317 single filament type bulb. BA15S base. In testing, directly comparable in light output to 6V incandescent bulb B317/B317B. Compatible with either negative or positive earth systems. Very low current draw - over 75% less than incandescent and halogen bulbs so great for low powered electrical systems. 6000K bright, white colour temperature. Good for Reverse applications. B307LEDWW or B317LEDA are better for indicator applications. Maximum diameter 18mm, total bulb height 43mm.

8 x 5050 SMD LED BA15D 12 Volt multi-directional bright white lamp. LED upgrade and direct replacement for B245D and B308B. BA15D base. In testing, brighter than c15W incandescent bulbs. Compatible with either negative or positive earth systems. Very low current draw - over 75% less than incandescent and halogen bulbs so great for low powered electrical systems. 6000K bright, white colour temperature. Applications include sidelights and repeaters, warning lights and number plate lights. 35mm total bulb length, 19mm maximum head diameter, no cover. For a warm white alternative see B308LEDWW.

30 x 4014 SMD LED BA15S 6 Volt multi-directional, 600 lumen bright RED lamp. LED upgrade and replacement for B317 type single filament bulb. BA15S base. Brighter than conventional 21W bulbs. Compatible with either negative or positive earth systems. Very low current draw - over 75% less than incandescent and halogen bulbs so great for low powered electrical systems. Bright RED colour temperature. This is NOT a combined stop & tail function bulb. Maximum diameter 18mm, total bulb height 43mm.

30 x 4014 SMD LED BA15D 6 Volt multi-directional 600 Lumen bright white lamp. Combined Stop & Tail (Brake & Rear) functionality. LED bulb option for B383B double filament type bulb with BA15D double contact base. Comparable in brightness to conventional 5/21W bulbs. Very low current draw - over 75% less than incandescent and halogen bulbs so great for low powered electrical systems. 6000K bright, white colour temperature. Maximum diameter 18mm, total bulb height 43mm. For a warmer white colour temperature, please see part number B383LEDWW

30 x 4014 SMD LED BA15D 12 Volt multi-directional bright white lamp. LED upgrade and replacement for B335 single filament 21W bulb with BA15D souble contact base. In testing, comparable in brightness to conventional 21W bulbs. Compatible with either negative or positive earth systems. Very low current draw - over 75% less than incandescent and halogen bulbs so great for low powered electrical systems. 6000K bright, white colour temperature. Maximum diameter 18mm, total bulb height 43mm. For a warmer white light please see B335LEDWW.

30 x 4014 SMD LED BA15S 12 Volt multi-directional warm white lamp. LED upgrade and replacement for B382B single filament type bulb. BA15S base. Brighter in testing than conventional incandescent 21W bulb B382B. Compatible with either negative or positive earth systems. Very low current draw - over 75% less than incandescent and halogen bulbs so great for low powered electrical systems. 3000K warm, white colour temperature for classic look. Indicator (warm white is usually the best LED colour option for behind an amber lens) or Reverse applications. If used as an indicator, an electronic flasher relay will be required of the correct polarity for your vehicle and also pin configuration, to suit your current wiring arrangement. Maximum diameter 18mm, total bulb height 43mm. For a bright white version of this lamp please see part number B382LEDW and for an amber indicator version B382LEDA

30 x 4014 SMD LED BA15S 6 Volt multi-directional warm white lamp. LED upgrade and replacement for B307 single filament type bulb. BA15S base. Compatible with either negative or positive earth systems. Very low current draw - over 75% less than incandescent and halogen bulbs so great for low powered electrical systems. In testing, comparable in light output to6V incandescent bulb B307B (15W). 3000K warm, white colour temperature. Indicator (best LED colour option of this bulb for behind an amber lens) or Reverse applications. If used as an indicator, an electronic flasher relay will be required of the correct polarity for your vehicle and also pin configuration, to suit your current wiring arrangement. Maximum diameter 18mm, total bulb height 43mm.

30 x 4014 SMD LED BA15D 12 Volt multi-directional warm white lamp. LED upgrade and replacement for B335 single filament 21W bulb with BA15D double contact base. In testing, comparable in brightness to a conventional 21W bulb. Compatible with either negative or positive earth systems. Very low current draw - over 75% less than incandescent and halogen bulbs so great for low powered electrical systems. 3000K warm, white colour temperature. Indicator (warm white often the best LED colour option for behind an amber lens) or Reverse applications. If used as an indicator, an electronic flasher relay will be required of the correct polarity for your vehicle and also pin configuration, to suit your current wiring arrangement. Maximum diameter 18mm, total bulb height 43mm. For a brighter white light please see B335LEDW

30 x 4014 SMD LED BA15D 6 Volt multi-directional 600 Lumen warm white lamp. Combined Stop & Tail (Brake & Rear) functionality. LED upgrade and replacement for B383B or B3214A double filament type bulbs with BA15D double contact base. In testing comparable in brightness to the 5/18W B3214A, for a brighter LED option please see part number B383LEDW bright white LED. Very low current draw - over 75% less than incandescent and halogen bulbs so great for low powered electrical systems. 3000K warm, white colour temperature. Maximum diameter 18mm, total bulb height 43mm.

30 x 4014 SMD LED BA15D 6 Volt multi-directional warm white lamp. LED upgrade and replacement for B319S single filament type bulb with BA15D double contact base. Comparable in brightness to B319S incandescent 18W bulbs with the benefit of LEDs. Compatible with either negative or positive earth systems. Very low current draw - over 75% less than incandescent and halogen bulbs so great for low powered electrical systems. 3000K warm, white colour temperature. Indicator (best LED colour option for behind an amber lens) or Reverse applications. If used as an indicator, an electronic flasher relay will be required of the correct polarity for your vehicle and also pin configuration, to suit your current wiring arrangement. Maximum diameter 18mm, total bulb height 43mm. For a bright whire version of the LED bulb please see part number B319LEDW.

A pair of resistors to be used with LED Indicators. One needed for each LED indicator to prevent rapid 'hyper' flashing if not using an LED flasher unit. Resistor size is 20mm x 20mm, Mounting plate 80mm x 50mm.

30 x 4014 SMD LED BAY15D 12 Volt multi-directional 600 Lumen bright RED lamp. Combined Stop & Tail (Brake & Rear) functionality. LED option for B380 double filament type bulb functionality with the common BAY15D offset pin, double contact base. Dual polarity. RED colour great for enhancing appearance behind red lenses. Very low current draw - over 75% less than incandescent and halogen bulbs so great for low powered electrical systems. Bright RED colour temperature. Maximum diameter 18mm, total bulb height 43mm. For an red LED option with number plate illumination and stop and tail functionality from two bright red cree LEDs, please see CSTLEDWWR-12Y

30 x 4014 SMD LED BAY15D 12 Volt multi-directional 600 Lumen bright white lamp. Combined Stop & Tail (Brake & Rear) functionality. LED option for B380 double filament type bulb replacement. Fitted with the common BAY15D offset pin, double contact base. Dual polarity. In testing, comparable in brightness to B380B and B3212B type 21/5W bulbs.  Very low current draw - over 75% less than incandescent and halogen bulbs so great for low-powered electrical systems. 6000K bright, white colour temperature. Maximum diameter 18mm, total bulb height 43mm. For a warm white option please see part number B380LEDWW, for a red LED option please see B380LEDR and for a LED option with number plate illumination and stop and tail functionality from two bright red Cree LEDs, please see CSTLEDWWR-12Y

30 x 4014 SMD LED BAY15D 6 &12 Volt multi-directional 600 Lumen warm white lamp. Combined Stop & Tail (Brake & Rear) functionality. LED option for B380 double filament type bulb replacement. Fitted with the common BAY15D offset pin, double contact base. Dual polarity. In testing, comparable in brightness to B380B and B3212B type 21/5W bulbs.  Very low current draw - over 75% less than incandescent and halogen bulbs so great for low powered electrical systems. 3000K warm, white colour temperature. Maximum diameter 18mm, total bulb height 43mm. For a bright white option please see part number B380LEDW, for a red LED option please see B380LEDR and for a LED option with number plate illumination and stop and tail functionality from two bright red cree LEDs, please see CSTLEDWWR-12Y

30 x 4014 SMD LED BAY15D 6 Volt multi-directional bright RED lamp. Combined Stop & Tail (Brake & Rear) functionality. RED option for B384 double filament type bulb with the common BAY15D offset pin, double contact base. RED colour is great for enhancing red colour behind red lenses. NEGATIVE EARTH ONLY! Very low current draw - over 75% less than incandescent and halogen bulbs so great for low-powered electrical systems. Bright RED colour temperature. Maximum diameter 18mm, total bulb height 43mm. Please also see part number CSTLEDWWR-6NY (Neg earth version) or CSTLEDWWR-6PY for a warm white number plate illumination, and two bright Cree LEDs for Stop and Tail function all in one bulb.

30 x 4014 SMD LED BAY15D 6 Volt multi-directional 600 Lumen bright white lamp. Combined Stop & Tail (Brake & Rear) functionality. LED option for B384 double filament type bulb replacement, with the common BAY15D offset pin, double contact base. In testing, comparable in brightness to B384XB and B3214B type 18/5W bulbs. NEGATIVE EARTH ONLY! Very low current draw - over 75% less than incandescent and halogen bulbs so great for low powered electrical systems. 6000K bright, white colour temperature. Maximum diameter 18mm, total bulb height 43mm. For a warm white option please see B384LEDWW and for red LED options please see B384LEDR and CSTLEDWWR-6NY (Neg Earth) or CSTLEDWWR-6PY (Pos Earth)

30 x 4014 SMD LED BAY15D 6 Volt multi-directional 600 Lumen warm white lamp. Combined Stop & Tail (Brake & Rear) functionality. LED option for B384 double filament type bulb with the common BAY15D offset pin, double contact base. In testing, comparable in brightness to B384XB and B3214B type 18/5W bulbs. NEGATIVE EARTH ONLY! Very low current draw - over 75% less than incandescent and halogen bulbs so great for low-powered electrical systems. 3000K warm, white colour temperature. Maximum diameter 18mm, total bulb height 43mm. For a bright white option please see B384LEDW and for red LED options please see B384LEDR and CSTLEDWWR-6NY (neg earth) or CSTLEDWWR-6PY (pos earth)

Combined WARM WHITE and AMBER multi direction, sidelight and indicator bulb. Accepts 6V and 12V input voltages. With offset pin BAY15D base. 12 super bright LEDs with integral lens. Warm white light for sidelight function, changing to bright AMBER for indication. This bulb should function normally with your existing flasher unit, in the unlikley event of LED 'Hyper flash' an electronic flasher relay will be required of the correct polarity for your vehicle (also pin configuration, to suit your current wiring arrangment). Compatible with either negative or positive earth systems. Very low current draw - over 75% less than incandescent and halogen bulbs so great for low powered electrical systems. 3000K warm, white colour temperature for sidelight, bright amber for indicator. Very Flexible application. A great compact and bright solution for easily converting classic sidelights to sidelight/indicator functionality. 18mm maximum diameter, 47mm total bulb height. For a bright white version of this great combination LED lamp please see part number CSILEDWY. For Equal pin BA15D versions please see CSILEDW and CSILEDWW.

BAY15D fitting Combined WHITE and AMBER multi-direction, sidelight and indicator bulb. Accepts 6V and 12V input voltages with BAY15D base. 12 super bright LEDs with an integral lens. Bright white light for sidelight function, changing to very bright AMBER for indication. This bulb should function normally with your existing flasher unit, in the unlikely event of LED 'Hyper flash' an electronic flasher relay will be required of the correct polarity for your vehicle (also pin configuration, to suit your current wiring arrangement). Compatible with either negative or positive earth systems. Very low current draw - over 75% less than incandescent and halogen bulbs so great for low-powered electrical systems. 6000K bright, white colour temperature for sidelight, bright amber for the indicator. Very flexible application. A great compact and bright solution for easily converting classic sidelights to sidelight/indicator functionality. 18mm maximum diameter, 47mm total bulb height. For a warm white version of this great combination LED lamp please see part number CSILEDWWY. For Equal pin BA15D versions please see CSILEDW and CSILEDWW. Base Pin Guide

12 x 3050 SMD Warm White LEDs and 6 x dual brightness 5050 LEDs for combined Number Plate Illumination, Stop and Tail lamp funtion. Multi direction bulb with 12 Volt application with equal pin BA15D base. 3000k warm white 360 degree light and bright RED colour temperature from 6 high power red LEDS. Red and white LEDs illuminate for tail light/number plate illumination functions - RED light intensifies when the brake is applied. Good contrast between red stop and tail light outputs. A great combination lamp. Accepts 9 to 50V input voltage so suitable for 12V and 24V NEGATIVE earth applications. Very low current draw - over 75% less than incandescent and halogen bulbs so great for low powered electrical systems. 18mm maximum diameter, 32mm total bulb height. The red light output is not quite as bright as the BAY15D part numbers (CSTLEDWWR-12Y, CSTLEDWWR-6NY and CSTLEDWWR-6PY) with their two cree LEDs behind a lens, but this is still a very bright, compact lamp, so a great option where space is limited. This is the ideal LED combination conversion lamp for Lucas Type L582 lamps with the BA15D fitting.

7 x 5050 SMD Warm White LED and 2 x High Power CREE LED combined Number Plate Illumination, Stop and Tail lamp. Multi direction bulb with 12 Volt application with offset pin BAY15D base and integral lens. 3000k warm white 360 degree light and bright RED colour temperature from 2 x Cree LEDS behind a lens. Red and white lights illuminate for tail light/number plate illumination function - then RED light intensifies when the brake is applied. Good contrast between red stop and tail light outputs. A great combination lamp. Compatible with NEGATIVE earth systems only. Very low current draw - over 75% less than incandescent and halogen bulbs so great for low powered electrical systems. 19mm maximum diameter, 50mm total bulb height. Please take care when fitting these bulbs - hold by the base and the lower warm white LED board section - NOT the ribbed aluminium lens section - to avoid damage from twisting.

7 x 5050 SMD Warm White LED and 2 x High Power CREE LED combined Number Plate Illumination and Stop and Tail lamp. Multi direction bulb with 6 Volt application with offset pin BAY15D base and integral lens. 3000k warm white 360 degree light and bright RED colour temperature from 2 x Cree LEDs behind a lens. Red and white lights illuminate for tail light/number plate illumination function - then RED light intensifies when the brake is applied. Good contrast between red stop and tail light outputs. A great combination lamp. Compatible with NEGATIVE earth systems only. Very low current draw - over 75% less than incandescent and halogen bulbs so great for low powered electrical systems. 19mm maximum diameter, 50mm total bulb height. Please take care when fitting these bulbs - please hold by the BA15 base and the lower warm white LED board section - NOT the ribbed aluminium lens section - to avoid damage from twisting.

15 x 39mm 6 Volt Festoon bulb - equivalent 39mm fitting to B253B but much brighter than 21W B1240B. 180 degree light from 6 x SMD 5730 LEDs. These LEDS are brighter than 5050 LEDs and hence the bulb features a finned aluminium heat sink on the rear. Compatible with either negative or positive earth systems. Very low current draw - over 75% less than incandescent and halogen bulbs so great for low powered electrical systems. 6000K bright, white colour temperature. 12.5mm wide LED section. For a 42mm LED festoon upgrade option for B1240, please see part number B1240LEDW

11 x 39mm 12V Festoon bulb - equivalent fitting to B239B. 360 degree/all round bright light from 12 x SMD 5050 LEDs. Compatible with either negative or positive earth systems. Very low current draw - over 75% less than incandescent and halogen bulbs so great for low powered electrical systems. 6000K bright, white colour temperature. 11mm LED section diameter, no cover. Much brighter than 5W B239B in testing, more comparable to 8W. See also B239LEDW-E for another 39mm Festoon LED upgrade. Two designs shown in photos, either design maybe supplied depending on available stock.

8 x 36mm slimline, dual sided, self-flashing 6V AMBER festoon bulb featuring six very bright 5730 SMD LEDs. A significant improvement on standard 3W incandescent festoon bulbs to improve visibility when indicating with a trafficator. Fits a number of trafficator arms including those fitted to the SF35 and SF40 arms as well as the common SE100/SF80 unit - part number 215. These bulbs do not fit all trafficator arms though, so please check dimensions: bulb cap 8.6mm diameter, bulb length 36mm, centre board thicknes 3mm, centre board width 14mm. No flasher relay or wiring modifcation is required - just fit in place of an ordinary festoon bulb and the bulb will flash automatically when the trafficator is activated. Compatible with either negative or positive earth systems. Very low current draw - over 75% less than incandescent and halogen bulbs so great for low-powered electrical systems. Very bright AMBER colour. Trafficator Maintenance Guide

8 x 36mm slimline, dual sided, self-flashing 12V AMBER festoon bulb featuring SIX very bright 5730 SMD LEDs. A significant improvement on standard 3W incandescent festoon bulbs to improve visibility when indicating with a trafficator. Fits a number of trafficator arms including those on the SF35 and SF40 units as well as the common SE100/SF80 unit - our part number 215. These bulbs do not fit all trafficator arms though, so please check dimensions: bulb cap 8.6mm diameter, bulb length 36mm, centre board thicknes 3mm, centre board width 14mm. No flasher relay or wiring modifcation is required - just fit in place of an ordinary festoon bulb and the bulb will flash automatically when the trafficator is activated. Compatible with either negative or positive earth systems. Very low current draw - over 75% less than incandescent and halogen bulbs so great for low powered electrical systems. Very bright AMBER colour. Trafficator Maintenance Guide

15 x 42mm 6 Volt Festoon bulb - equivalent fitting to B618F and a good LED upgrade option for that 18W bulb, proving much brigher in testing. 180 degree light from 15 x 4014 LEDs. Compatible with either negative or positive earth systems. Input voltage 6 to 10V. Very low current draw - over 75% less than incandescent and halogen bulbs so great for low powered electrical systems. 6000K bright, white colour temperature. For a less bright LED replacement option please see part number B818LEDW-B Two designs shown in photos, either design maybe supplied depending on available stock.

15 x 3030 SMD LED 6V High Power lamp with integral lens. WEDGE T15 W16W type - fits the same connector as WEDGE T10, just a larger bulb. 360 degree very bright AMBER light. 6V LED option equivalent to 12V 21W bulb type B921A, though much brighter than conventional 21W bulbs in testing. Compatible with either negative or positive earth systems. Very low current draw - over 75% less than incandescent and halogen bulbs so great for low powered electrical systems. Bright AMBER colour temperature. Integral lens. Total bulb length 52mm, bulb diameter 15mm. For correct indicator function an electronic flasher relay will be required of the correct polarity for your vehicle and also pin configuration, to suit your current wiring arrangement. For the bright white version of this bulb please see part number B921-6LEDW

Amber 15 x 3030 SMD LED 12V High Power lamp with lens. WEDGE T15 W16W type - fits the same connector as WEDGE T10, just a larger bulb. 360 degree very bright AMBER light with an integral lens to boost light output further. Much brighter in testing than amber T15 incandescent bulb B921A (21W). Compatible with either negative or positive earth systems. Very low current draw - over 75% less than incandescent and halogen bulbs so great for low powered electrical systems. Bright AMBER colour temperature. Integral lens, 52mm total bulb length, 15mm head diameter. For correct indicator function an electronic flasher relay will be required of the correct polarity for your vehicle and also pin configuration, to suit your current wiring arrangement. Most commonly 12V, 3 pin, negative earth/ground LEDFLASH3. For a bright white version of this LED lamp, please see part number B921LEDW

12 x 3014 SMD LED BA15S 6 Volt multi-directional bright white lamp. LED upgrade and replacement for B205. BA15S base. In testing, comparable in brightness to 6V incandescent bulb B205 (5W). Clear glass 19mm diameter LED cover. Compatible with either negative or positive earth systems. Very low current draw - over 75% less than incandescent and halogen bulbs so great for low powered electrical systems. 6000K bright, white colour temperature. A really neat bulb for vintage and classic vehicles - LED performance with the look of a conventional bulb.

8 x 5050 SMD LED BA15D 12 Volt multi-directional warm white lamp. LED upgrade and direct replacement for B245D and B308B. BA15D base. In testing, brighter than c15W incandescent bulbs. Compatible with either negative or positive earth systems. Very low current draw - over 75% less than incandescent and halogen bulbs so great for low powered electrical systems. 3000K warm, white colour temperature. Applications include sidelights and repeaters, dash lights and number plate lights. 35mm total bulb length, 19mm maximum head diameter, no cover. For a brighter white alternative please see B308LEDW.

9 x 5050 SMD LED BA15S 12 Volt multi-directional RED lamp. Red LED upgrade bulb. In testing much brighter than B207BR. BA15S base. Compatible with either negative or positive earth systems. Very low current draw - over 75% less than incandescent and halogen bulbs so great for low powered electrical systems. RED colour. Applications include rear lights. 37mm total bulb length, 20mm head diameter, no cover.

30 x 4014 SMD LED BA15D 6 Volt multi-directional bright white lamp. LED upgrade and replacement for B319B single filament type bulb with BA15D souble contact base. Comparable in brightness to 6V 21W bulbs with the benefits of LED. Compatible with either negative or positive earth systems. Very low current draw - over 75% less than incandescent and halogen bulbs so great for low powered electrical systems. 6000K bright, white colour temperature. Maximum diameter 18mm, total bulb height 43mm. For a warm white version please see part number B319LEDWW

Very bright Cree LED MCC BA9S multi-directional bright white lamp. Accepts voltage input 10 to 30V. LED upgrade bulb with BA9S base - brighter than 23W incandescent bulb B419. Compatible with either negative or positive earth systems. Very low current draw - over 75% less than incandescent and halogen bulbs so great for low powered electrical systems. 6000K bright, white colour temperature. Applications include warning lights and indicators. Integral lens, 12.5mm head diameter, 45mm diameter overall bulb length. For an amber version of this LED bulb, please see part number B418LEDA

20 x 2835 SMD LED WEDGE T10 6 Volt multi-directional bright white lamp. Bright LED upgrade bulb with WEDGE T10 base. Compatible with either negative or positive earth systems. Very low current draw - over 75% less than incandescent and halogen bulbs so great for low powered electrical systems. 6000K bright, white colour temperature. 32mm total bulb length, 11mm head diameter, no cover. In testing, brighter than 10W conventional bulbs. For some 6V T10 LED alternatives please see B117LEDWW-A, B117ALEDWW and B117BLEDW

15 x 3030 SMD LED 6V High Power lamp with integral lens. WEDGE T15 W16W type - fits the same connector as WEDGE T10, just a larger bulb. 360 degree very bright white light. 6V LED equivalent to 12V bulb number B921 (21W), though much brighter than 21W bulbs in testing. Compatible with either negative or positive earth systems. Very low current draw - over 75% less than incandescent and halogen bulbs so great for low powered electrical systems. 6000K bright, white colour temperature. Integral lens. 52mm total bulb length, 15mm head diameter. For the amber version of this bulb please see part number B921A-6LEDA

White 15 x 3030 SMD LED 12V High Power lamp with lens. WEDGE T15 W16W type - fits the same connector as WEDGE T10, just a larger bulb. 360 degree very bright white light with an integral lens to boost light output further. Much brighter in testing than clear T15 incandescent bulb B921 (21W). Compatible with either negative or positive earth systems. Accepts voltage input 10 to 30V. Very low current draw - over 75% less than incandescent and halogen bulbs so great for low powered electrical systems. 6000K bright, white colour temperature. 15mm diameter, 52mm long. For a bright amber version of this LED lamp, please see part number B921ALED