Heavy surface fitting door lock suitable for heavier doors, 78mm x 76mm approx with lever to top. Body stands 19mm proud of mounting panel, with facility for square (6mm size which can be opened out) handle shaft to engage in the lever. The cast brass body is offered in chrome OR nickel plated finish. -- nickel plated finish

Heavy surface fitting door lock suitable for heavier doors, 78mm x 76mm approx with lever to top. Body stands 19mm proud of mounting panel, with facility for square (6mm size which can be opened out) handle shaft to engage in the lever. The cast brass body is offered in chrome OR nickel plated finish. -- nickel finish

Replacement dovetail wedge and nut only (no mounting plate). Dimensions - wedge 20mm across (wide end) 11mm across (narrow end) 22mm deep. 5/16" stud 35mm long (18mm threaded section).

Wide mounting plate (TD/TF type) complete with wedge. Mounting plate 95mm x 34mm

Narrow mounting plate (early T type) and wedge complete. Mounting plate 95mm x 20mm

Face mounting plate (suit Cobra, Healey) and wedge complete. Mounting plate 95mm x 33mm,

Replacement cover only, for our 601 Silent Travel door locks, measures approx 63mm x 75mm.

Replacement cover only, for our 601 Silent Travel door locks, measures approx 63mm x 75mm. --

Replacement cover only, for our 601 Silent Travel door locks, measures approx 63mm x 75mm. --

'Silent-travel' lock, as used on MG and other pre-war cars, chrome finish 63mm wide 75mm tall body, chrome cover. Facility for shaft of exterior handle to fit into back. Use striker plate part numbers 602N, 602W, 602F or wedge 602D. Square hole for handle shaft approx 20mm from face edge.

'Silent-travel' lock, as used on MG and other pre-war cars, chrome finish 63mm wide 75mm tall body, chrome cover. Facility for shaft of exterior handle to fit into back. Use striker plate part numbers 602N, 602W, 602F or wedge 602D. Square hole for handle shaft approx 20mm from face edge. --

'Silent-travel' lock, as used on MG and other pre-war cars, chrome finish 63mm wide 75mm tall body, chrome cover. Facility for shaft of exterior handle to fit into back. Use striker plate part numbers 602N, 602W, 602F or wedge 602D. Square hole for handle shaft approx 20mm from face edge. --

Surface mount lightweight door lock with stainless steel cover plate. Rear pull to open, no provision for shaft of external handle. Mounting screws 33mm horizontal, 44.5mm vertical. The lock tongue can be fitted as shown or reversed and the protrusion can be adjusted from approx 9mm to 16mm by screw thread shaft at rear. The cover stands approx 18mm proud of the panel.

Heavy surface fitting door lock suitable for heavier doors, 78mm x 76mm approx with lever to top. Body stands 19mm proud of mounting panel, with facility for square (6mm size which can be opened out) handle shaft to engage in the lever. The cast brass body is offered in chrome OR nickel plated finish.

Heavy surface fitting door lock suitable for heavier doors, 78mm x 76mm approx with lever to top. Body stands 19mm proud of mounting panel, with facility for square (6mm size which can be opened out) handle shaft to engage in the lever. The cast brass body is offered in chrome OR nickel plated finish. -- chrome plated finish

Heavy surface fitting door lock suitable for heavier doors, 78mm x 76mm approx with lever to top. Body stands 19mm proud of mounting panel, with facility for square (6mm size which can be opened out) handle shaft to engage in the lever. The cast brass body is offered in chrome OR nickel plated finish. -- chrome plated finish

Surface fitting lock with top lever action. Base 51mm x 86mm zinc plated. With a little handle adaptation this lock can be modified quite easily to assume a vintage appearance. Square hole for handle shaft approx 17mm from face edge. --

Surface fitting lock with top lever action. Base 51mm x 86mm zinc plated. With a little handle adaptation this lock can be modified quite easily to assume a vintage appearance. Square hole for handle shaft approx 17mm from face edge. --

Small chromium plated, surface mount door lock with lever to top, of a design common to many 'vintage' locks. Base size 86mm x 51mm approx. Original early Morgan style. Square hole for handle shaft approx 18mm from face edge.

Small chromium plated, surface mount door lock with lever to top, of a design common to many 'vintage' locks. Base size 86mm x 51mm approx. Original early Morgan style. Square hole for handle shaft approx 18mm from face edge. --

Small chromium plated, surface mount door lock with lever to top, of a design common to many 'vintage' locks. Base size 86mm x 51mm approx. Original early Morgan style. Square hole for handle shaft approx 18mm from face edge. --

Surface fitting door lock, with a lever handle similar to pre-war shape. Base size approx 87mm x 51mm with a long tongue, particularly suitable for open bodywork, plated finish. Square hole for handle shaft approx 20mm from face edge.

Surface fitting door lock, with a lever handle similar to pre-war shape. Base size approx 87mm x 51mm with a long tongue, particularly suitable for open bodywork, plated finish. Square hole for handle shaft approx 20mm from face edge. --

Surface fitting door lock, with a lever handle similar to pre-war shape. Base size approx 87mm x 51mm with a long tongue, particularly suitable for open bodywork, plated finish. Square hole for handle shaft approx 20mm from face edge. --

Surface fitting door lock, 80mm x 60mm x 15mm deep, plated finish.

Remote action cast brass door lock complete with lever mechanism. Lock 83mm x 89mm brass finish. Overall length of lock to lever (handle mounting) 340mm. Use with striker plate part numbers 541 or 542. Machined bronze latch case with plated steel components, lever mechanism, mounting plate etc.